Eshop roka 2025 s vykurovacou technikou

WAFER J9 - mellanflänsklapp, niklert guss; EPDM - DN 100; L=52 mm BRA.J9.100

Kod för översättningen: J9.100.100
Inte betygsatt Information om betyg
1 816,97 kr –20 %
Vykurovacia technika Medziprírubová uzatváracia klapka WAFER J9 - disk nikl. liatina; EPDM - DN 100; L=52mm
1 816,97 kr –20 % 1 453,60 kr / st 1 181,79 kr exkl. moms Pris för åtgärden:
Internationell leverans
I lager hos leverantören

Detaljerad information

Detaljerad beskrivning av produkten

Ställdon WAFER J9, BRA.J9.100, storlek: DN 100, längd: 52 mm

 

  • max. tryck 16 bar, flänsar PN16/PN10/PN6 enligt STN EN 1092-1
  • T = -10 °C till +120 °C
  • för uppvärmning och luftkonditionering, vattenfördelning, tryckluft
  • material: kropp - järn GJS 400-15, disk - niklbelagd järn
  • material packning/linning: EPDM
  • låsbar styrhånter
  • ej lämplig för ånga och vätskor med olja eller kolväten 

Vanliga frågor

  • Hur väljer jag rätt typ och storlek på armatur/ventil? Följ den angivna nömningstryck (PN) och drifttemperatur (T) i tekniska specifikationer - de måste motsvara eller överstiga de faktiska driftvillkor i ditt system, och anslutningsstorleken måste matcha rörets diameter.
  • Hur fungerar denna armatur/ventil? Den exakta funktionen (stängning, tryckreglering, bakflöde osv.) beror på typen - en detaljerad beskrivning av funktionen finns ovanför detta produkt.
  • Måste installationen utföras av en yrkesman? För enklare ställarmaturer kan installationen utföras av en hobbyist, för reglerings- och säkerhetsarmaturer (säkerhetsventiler, tryckminskningsventiler) rekommenderar vi alltid en yrkesman, eftersom det gäller komponenter med säkerhetsfunktion.

Ytterligare parametrar

Kategori: BRA.J9.100 vridspjällsventiler WAFER J9 - spjäll i förnicklat gjutjärn
Garanti: 2 år
Vikt: 4.15 kg
Tillgänglighet: I lager eller hos leverantören
Senaste prisuppdatering: 13.04.2026 1:05:56

Produktbetyg

Bli den första som publicerar en artikel till denna post!

Fyll inte i detta fält

Hur skulle du betygsätta den här produkten? Välj 1 till 5 stjärnor, där 1 är det sämsta och 5 är det bästa betyget.

Diskussion

Fyll inte i detta fält

Lista över diskussioner

P Författarens avatar 13.11.2026 19:45
Dobar dan, planiram ugraditi ovu klapku na cijev DN 100 za sustav grijanja koji radi pod tlakom do 12 bara i temperaturama do 100 stupnjeva. Je li ova dimenzija od 52 mm dovoljna za montažu između dvije standardne priključne ploče?
A Författarens avatar 13.11.2026 19:45
Da, ta klapka je dizajnirana upravo za takve uvjete jer izdržava tlak do 16 bar i temperature do +120 °C, što pokriva vaše potrebe. Duljina od 52 mm omogućuje jednostavnu ugradnju tipa "wafer" između dva spoja. Za ovu namjenu materijal EPDM brtve je sasvim adekvatan.
R Författarens avatar 16.10.2026 15:06
Dobrý deň prajem, chcel by som vedieť, či túto klapku môžem použiť na vykurovanie, keďže sa tam teplota pohybuje okolo 80 stupňov a v návode píšem, že je do 120? A tiež je to isté pre vodu?
A Författarens avatar 16.10.2026 15:06
Áno, táto klapka je určená práve pre vykurovacie systémy a rozvody vody. Jej tesnenie z EPDM a liatinové telo vydrží teploty od mínus desiatich až po sto dvadsať stupňov Celzia, takže pri vašej teplote 80 stupňov bude fungovať bez problémov. Je však dôležité si dať pozor, aby ste ju nepoužili na paru alebo s olejmi.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.